 |
 |
 |
|
Dodge Charger Painted Body Side Moldings, 4pc 2015 - 2023
Set of 4 - 1.25" wide door moldings
Self-Adhering Painted Body-Side Moldings protect your car from scratches and door dings while adding a more sophisticated look than traditional molding.
- Painted Body Side Molding Kit comes complete with Easy-to-Follow Installation Instructions, Pro-Clean™ Prep Pads, and Pro-Bond™ Adhesive Promoter
- 100% Paint Match Guarantee
- 5-Year/50,000 Mile Warranty
- Made in the USA
- Added Protection against shopping carts, door dings, scratches, chipping, and other road hazards
- High Quality Automotive Grade ABS Synthetic Materials
- OEM Quality
- Measured, Pre-Cut, and Precision Engineered to match your Dodge Charger
- Quick and Easy No-Drill Installation with the use of Self-Adhering 3M Tape
***Be sure to type color code in space provided for exact match***
Installing Painted Body Side Moldings on Your VehicleBody side molding isn’t just a way to keep nicks out of your car doors. It also looks sleek and sporty on the side of your car. Affordable changes like this can set your car or truck apart from the rest. You want to make sure you install the body side molding correctly. Otherwise, you’ll end up with uneven molding that can make your car look dented (exactly what you’re trying to avoid). Here are some tips on installing your body side molding properly.
Preparation Tools you’ll need: Tape Measure Masking Tape Grease Pencil Clean Soft Towel
Installation - Clean the surface where you’ll be installing the body side molding.
- Check the installation sheet that comes with the kit to ensure proper measurements.
- Make two marks with the grease pencil to indicate where the molding will begin and end along the side of your car.
- Connect the marks using masking tape.
- Clean the surface again with the alcohol pads included in the kit.
- Repeat all of these steps on the other side of the vehicle.
Along the line of masking tape, apply a thin layer of the Pro-Bond adhesive that comes with your moldings kit to both sides of the car. The installation sheet will give you the correct molding start points. Peel just the edges of the liner that are attached to the molding, then place the molding along the masking tape line gently, removing the liner that is underneath. Using a soft cloth, wipe down firmly to make sure the molding sticks.
And last - enjoy your new moldings!!!!!
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
Type of Paint:
Body Side Moldings are painted with 3 layers of Onyx-HD Waterborne Paint, and 2 layers of clear coat, just like OEM does so that they will match your vehicle perfectly. All products are thoroughly inspected, buffed, and polished to a showroom-finish.
Where to find your paint code:
In most cases, the paint code can be found on the tag of your vehicle which is usually on the driver side door jamb, or near the glovebox area. If you cannot locate your paint code, you can contact any dealership and give them your VIN # and they can locate it for you.
- Adds protection from dings, dents, & parking lot damage.
- Adds style to your vehicle to make it stand out from the rest.
- 100% made in the USA
- Made of high-quality ABS composite materials.
- Painted to match your vehicle using the same paint as OEM.
Measured, pre-cut, & precision engineered to fit your vehicle.
- Includes 4 Painted Body Side Molding pieces (1 piece for each door), easy-to-follow installation instructions with vehicle-specific diagrams, 2 Alcohol Pads, and 2 Pro-Bond Adhesive Promoter Crush Swabs (all you will need is a tape measure, masking tape, and a grease pencil).
- Quick & easy no-drill install with the use of 3M double-sided automotive-grade adhesive tape.
|
|
|
|
|
|
|
